Hi Q Telecom Inc.

Step-by Step Instructions for the Installation and Programming of the T-Lock with Allowed and Disallowed Memory

SAFETY INSTRUCTIONS:

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

    1. Read and understand all instructions.
    2. Follow all warnings and instructions marked on the product.
    3. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
    4. This product should be operated from the telephone line only.
    5. Never push objects of any kind into this product except a telephone line cord as other objects may touch dangerous voltage points that could result in risk of fire or electric shock. Never spill liquid of any kind on the product.
    6. Refer servicing to qualified service personnel under the following conditions:

      If liquid has been spilled into the product.
      If the product has been exposed to rain or water.
      If the product does not operate normally by following the operating instructions.
      If the product has been dropped.
      If the product exhibits a distinct change on performance.

    7. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightening.

    8. Do not use the telephone to report a gas leak in the vicinity of the leak.

INSTALATION INSTRUCTIONS:

The T-Lock comes with two (2) RJ11 jacks, one on each side.  One side is labeled “Telephone”, the other other is labeled “Line”. We also include a short RJ11 patch cord for your convenience.
1) Unplug your RJ11 cord from your (existing) telephone.
2) Plug your (existing) RJ11 cord to the RJ11 jack on the T-Lock labeled “Line”.
3) Plug the provided short RJ11 patch cord to the side labeled “Telephone” and the other end to your (existing) telephone.
Now you are ready to start programming your T-Lock!

PROGRAMING:

The best way to program the T-Lock on a live telephone line is to call the line that the dial is installed on from your cell phone or other telephone.  When the phone that the dialer is connected to rings answer it and begin your programming.  Leave the other phone that you called from off hook so you have a silent connection with no interruptions from the local operating company while you program. 

Important: Your T-Lock is preset at the factory to ALLOW all calls.  Therefore, you only need to program the ALLOW numbers IF you first DISALLOW certain calls such as 1+, 0+, or 1+ area code calls.  The default programming passcode is 54321*. 

To DISALLOW specific numbers:
54321*
00 32 Disallowed-number1 ##
00 32 Disallowed-number2 ##
…
00 32 Disallowed-number 100 ##
hangup

Examples:
54321*                          Entering programming mode
00 32 1 ##                     Blocks 1+ calls (long distance calls)
00 32 0 ##                     Blocks 0+ calls (operators assisted calls)
00 32 011 ##                 Blocks 011+ calls (international calls –from US)
00 32 411 ##                 Blocks calls to 411 (directory assistance)
00 32 1 305 ##               Blocks calls starting with 1-305 area code
00 32 305 558 5577 ##  Blocks calls to 305-558-5577 (10 digit dialing)
00 32 558 5577 ##         Blocks calls to 558-5577 (7 digit dialing)
00 32 1900 ##                Blocks calls to 1-900 numbers
hangup 

To ALLOW specific numbers:
54321*
00 00 Allowed-Number1 ##
00 00 Allowed-Number2 ##
….
00 00 Allowed Number 100 ##
hangup

Examples:
54321*                          Entering programming mode
00 10 1 ##                     Allows calls to any LD number that start with 1
00 10 1 305##               Allows all any number in area code 1305
00 10 1 305 558##        Allows calls to starting with 1-305-558
00 10 305 558 5577##  Allows calls to 305-558-5577
hangup
Note: keep in mind that the numbers to block are the same you would need to dial

Change the programming passcode:
54321*
00 34 New_Passcode ##
hangup

The programming passcode can be any combination of digits (0-9), # or *.
54321*                           Factory default
00 34 1234 ##                Changes passcode to 1234
00 34 12345 ##              Changes passcode to 12345

Restore factory defaults 
54321*
99 (wait to hear beep)
1   (wait to hear beep)
hangup

Use this instructions in case you need to reset your T-Lock list of allowed & disallowed numbers.  Important: If you changed the programming passcode and cannot remember it or the memory has been corrupted and cannot enter programming mode go online and refer to Hardware reset instructions (below).

Bypass code
111  is the default bypass code. 
111, wait for dialtone, then dial any restricted number

If you programmed your T-Lock to disallow certain numbers, you can then use the bypass code to bypass restrictions and dial those restricted numbers, on a per call basis. 
To change the factory default bypass code follow these steps:
54321*                          Entering programming mode
00 35  new-code ##       Enter any number (1 to 16 digits)

WARRANTY & REPAIR SERVICE:

Hi Q TeleCOM Inc. warrants its products to be free of defects of material and workmanship for a period of one (1) year from the date of shipment. All items to be repaired under warranty are to be sent, together with the original sales slip, transportation prepaid to:
HiQ TeleCom Inc.
8004 NW 154 ST # 401
Miami, FL 33016
Product will be repaired or replaced at HQT’s option and returned "NO COST" provided in HQT’s opinion the item(s) have not been improperly installed, damaged or altered without authorization.

HARDWARE RESET INSTRUCTIONS:
If you loose, forget your own security passcode (default as 54321*), you will need to follow the instructions below to perform a hardware reset on this unit.

Circuit Diagram
 Preparation: You will need to open the black enclusre with a thin flat-headed screw driver. You will also need a piece of metal to make contact with the two terminals as described below.
Revision A & B

Step 1
Short the two reset pads together with  something metallic.

Step 2
While shorting the two pads take the telephone handset off hook and wait one
second, then remove the short.

Step 3
You should hear two beeps through the telephone handset confirming that the unit has been defaulted.

Revision C

Step 1
Press and hold the factory reset button.

Step 2
While holding the button down take the telephone handset off hook and wait one second, then release the button.

Step 3
You should hear two beeps through the telephone handset confirming that the unit has been defaulted.

For additional information, visit http://hqtelecom.com or contact us.

1995 - 2006 Hi Q Telecom Inc. All rights reserved